[FluidNC Issue#1584] Problem:

Wiki Search Terms

How to fill macros on cyd pendant

Controller Board

Image

Input Circuits

Configuration file

board: 6 Pack
name: 6 Pack External XYYZ 10V VFD
meta: 2025-1-09
stepping:
  engine: I2S_STREAM
  idle_ms: 250
  pulse_us: 4
  dirdelayus: 1
  disabledelayus: 0
  
axes:
  sharedstepperdisablepin: NOPIN
  x:
    stepspermm: 262.2529
    maxratemmpermin: 17000
    accelerationmmper_sec2: 2500
    maxtravelmm: 1270
    soft_limits: true
    homing:
      cycle: 2
      positive_direction: true
      mpos_mm: 0.000
      feedmmper_min: 1000
      seekmmper_min: 1800
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.32:low
      hard_limits: false
      pulloff_mm: 3
      standard_stepper:
        step_pin: I2SO.1
        direction_pin: I2SO.0
        disablepin: NOPIN
  y:
    stepspermm: 453.3212
    maxratemmpermin: 13000
    accelerationmmper_sec2: 1400
    maxtravelmm: 2530
    soft_limits: true
    homing:
      cycle: 2
      positive_direction: true
      mpos_mm: 0.000
      feedmmper_min: 800
      seekmmper_min: 1950
      settle_ms: 500
      seek_scaler: 1.10
      feed_scaler: 1.100
    motor0:
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.35:low
      hard_limits: false
      pulloff_mm: 4
      standard_stepper:
        step_pin: I2SO.4
        direction_pin: I2SO.3
        disablepin: NOPIN
    
    motor1:
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: false
      pulloff_mm: 4
      standard_stepper:
        step_pin: I2SO.7
        direction_pin: I2SO.6
        disablepin: NOPIN
  z:
    stepspermm: 131.125
    maxratemmpermin: 12000
    accelerationmmper_sec2: 1500
    maxtravelmm: 280
    soft_limits: true
    homing:
      cycle: 1
      positive_direction: true
      mpos_mm: 150.000
      feedmmper_min: 800
      seekmmper_min: 1000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.34:low
      hard_limits: false
      pulloff_mm: 5
      standard_stepper:
        step_pin: I2SO.10
        direction_pin: I2SO.9
        disablepin: NOPIN
probe:
  pin: gpio.39:low
  checkmodestart: true
 
i2so:
  bck_pin: gpio.22
  data_pin: gpio.21
  ws_pin: gpio.17
spi:
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18
sdcard:
  carddetectpin: NO_PIN
  cs_pin: gpio.5
start:
  must_home: false
macros:
  startup_line0:$x
  startup_line1:
  macro0: G54Y0X0f4000
  macro1: G10L20P1Y0X0Z0
  macro2:
  macro3:
  after_homing: 
  after_reset:
  after_unlock:
uart2:
  txd_pin: gpio.25
  rxd_pin: gpio.27
  rtspin: NOPIN
  ctspin: NOPIN
  baud: 1000000
  mode: 8N1
uart_channel2:
  reportintervalms: 75
  uart_num: 2
control:
  safetydoorpin: NO_PIN
  resetpin: NOPIN
  feedholdpin: NO_PIN
  cyclestartpin: NO_PIN
  macro0_pin: gpio.36:low
  macro1_pin: 
  macro2pin: NOPIN
     
coolant:
  flood_pin:gpio.12
  mistpin: NOPIN
  delay_ms: 0
  
10V:
  forward_pin: gpio.26
  reverse_pin: gpio.14
  pwm_hz: 5000
  output_pin: gpio.4
  enablepin: NOPIN
  directionpin: NOPIN
  disablewiths0: false
  s0withdisable: true
  spinup_ms: 0
  spindown_ms: 0
  tool_num: 0
  speed_map: 0=0.000% 24000=100%
  offonalarm: false

Startup Messages

NO MACRO

User Interface Software

CYD PENDANT

What happened?

I want to fill in the macro

GCode File

No response

Other Information

No response