> 未分类 > [FluidNC Issue#1542] Problem: Configure wifi webpage reports incorrect settings after save

[FluidNC Issue#1542] Problem: Configure wifi webpage reports incorrect settings after save

未分类 bolang 4个月前 (10-14) 37次浏览

Issue #1542 | 状态: 已关闭 | 作者: TomKamphuys | 创建时间: 2025-08-10

Wiki Search Terms

wifi configuration setup

Controller Board

6-pack

Machine Description

No machine at all. Laptop -> usb cable -> esp32 board

Input Circuits

Configuration file

n.a.

Startup Messages

n.a.

User Interface Software

n.a.

What happened?

I changes the wifi configuration and clicked save. I expected that the entered names would have been taken over.

GCode File

n.a.

Other Information

I changes the wifi configuration and clicked save. I expected that the entered names would have been taken over, but it hasn’t.

Image

The (changed) hostname ‘fluidnc’ -> ‘fluidnc3’ has been prepended to the (changed) SSID ‘NearFieldScanner’ -> ‘fluidnc3NearFieldScanner’. That has in turn be prepended to the (changed) Access Point SSID ‘FluidNC3’ -> ‘fluidnc3NearFieldScannerFluidNC3’

I’m trying to setup 3.9.8 after a fresh install.

评论 (5)

#1 – bdring 于 2025-08-10

Try setting fields manually from the console and checking the value.

http://wiki.fluidnc.com/en/features/wifi_bt#wifi-settings

Send $STA/SSID=
Then send $STA/SSID to check the value.

Show us the console session.

#2 – TomKamphuys 于 2025-08-10

Full Output:

[15:09:43] [ usb ports ] Detected a change in available ports: [COM6][COM5]
[15:09:47] [ connect ] PORT INFO: Port is now open: COM5 - Attempting to detect Controller...
[15:09:47] [ connect ] Attempting to detect Controller (1): (Autoreset)
[15:09:47] [ ] ok
[15:09:48] [ connect ] Attempting to detect Controller (2): (Ctrl+X)
[15:09:48] [ ] Grbl 3.9 [FluidNC v3.9.8 (wifi) '$' for help]
[15:09:49] [ connect ] Firmware Detected: FluidNC version 3.9.8 dated on COM5
[15:09:50] [ $CD ] board: None
[15:09:50] [ $CD ] name: Default (Test Drive no I/O)
[15:09:50] [ $CD ] meta:
[15:09:50] [ $CD ] stepping:
[15:09:50] [ $CD ] engine: RMT
[15:09:50] [ $CD ] idle_ms: 255
[15:09:50] [ $CD ] pulse_us: 4
[15:09:50] [ $CD ] dirdelayus: 0
[15:09:50] [ $CD ] disabledelayus: 0
[15:09:50] [ $CD ] segments: 12
[15:09:50] [ $CD ] spi:
[15:09:50] [ $CD ] misopin: NOPIN
[15:09:50] [ $CD ] mosipin: NOPIN
[15:09:50] [ $CD ] sckpin: NOPIN
[15:09:50] [ $CD ] sdcard:
[15:09:50] [ $CD ] cspin: NOPIN
[15:09:50] [ $CD ] carddetectpin: NO_PIN
[15:09:50] [ $CD ] frequency_hz: 8000000
[15:09:50] [ $CD ] kinematics:
[15:09:50] [ $CD ] Cartesian:
[15:09:50] [ $CD ] axes:
[15:09:50] [ $CD ] sharedstepperdisablepin: NOPIN
[15:09:50] [ $CD ] sharedstepperresetpin: NOPIN
[15:09:50] [ $CD ] homing_runs: 2
[15:09:50] [ $CD ] x:
[15:09:50] [ $CD ] stepspermm: 80.000000
[15:09:50] [ $CD ] maxratemmpermin: 1000.000000
[15:09:50] [ $CD ] accelerationmmper_sec2: 25.000000
[15:09:50] [ $CD ] maxtravelmm: 1000.000000
[15:09:50] [ $CD ] soft_limits: false
[15:09:50] [ $CD ] motor0:
[15:09:50] [ $CD ] limitnegpin: NO_PIN
[15:09:50] [ $CD ] limitpospin: NO_PIN
[15:09:50] [ $CD ] limitallpin: NO_PIN
[15:09:50] [ $CD ] hard_limits: false
[15:09:50] [ $CD ] pulloff_mm: 1.000000
[15:09:50] [ $CD ] null_motor:
[15:09:50] [ $CD ] y:
[15:09:50] [ $CD ] stepspermm: 80.000000
[15:09:50] [ $CD ] maxratemmpermin: 1000.000000
[15:09:50] [ $CD ] accelerationmmper_sec2: 25.000000
[15:09:50] [ $CD ] maxtravelmm: 1000.000000
[15:09:50] [ $CD ] soft_limits: false
[15:09:50] [ $CD ] motor0:
[15:09:50] [ $CD ] limitnegpin: NO_PIN
[15:09:50] [ $CD ] limitpospin: NO_PIN
[15:09:50] [ $CD ] limitallpin: NO_PIN
[15:09:50] [ $CD ] hard_limits: false
[15:09:50] [ $CD ] pulloff_mm: 1.000000
[15:09:50] [ $CD ] null_motor:
[15:09:50] [ $CD ] z:
[15:09:50] [ $CD ] stepspermm: 80.000000
[15:09:50] [ $CD ] maxratemmpermin: 1000.000000
[15:09:50] [ $CD ] accelerationmmper_sec2: 25.000000
[15:09:50] [ $CD ] maxtravelmm: 1000.000000
[15:09:50] [ $CD ] soft_limits: false
[15:09:50] [ $CD ] motor0:
[15:09:50] [ $CD ] limitnegpin: NO_PIN
[15:09:50] [ $CD ] limitpospin: NO_PIN
[15:09:50] [ $CD ] limitallpin: NO_PIN
[15:09:50] [ $CD ] hard_limits: false
[15:09:50] [ $CD ] pulloff_mm: 1.000000
[15:09:50] [ $CD ] null_motor:
[15:09:50] [ $CD ] control:
[15:09:50] [ $CD ] safetydoorpin: NO_PIN
[15:09:50] [ $CD ] resetpin: NOPIN
[15:09:50] [ $CD ] feedholdpin: NO_PIN
[15:09:50] [ $CD ] cyclestartpin: NO_PIN
[15:09:50] [ $CD ] macro0pin: NOPIN
[15:09:50] [ $CD ] macro1pin: NOPIN
[15:09:50] [ $CD ] macro2pin: NOPIN
[15:09:51] [ $CD ] macro3pin: NOPIN
[15:09:51] [ $CD ] faultpin: NOPIN
[15:09:51] [ $CD ] estoppin: NOPIN
[15:09:51] [ $CD ] homingbuttonpin: NO_PIN
[15:09:51] [ $CD ] coolant:
[15:09:51] [ $CD ] floodpin: NOPIN
[15:09:51] [ $CD ] mistpin: NOPIN
[15:09:51] [ $CD ] delay_ms: 0
[15:09:51] [ $CD ] probe:
[15:09:51] [ $CD ] pin: NO_PIN
[15:09:51] [ $CD ] toolsetterpin: NOPIN
[15:09:51] [ $CD ] checkmodestart: true
[15:09:51] [ $CD ] hard_stop: false
[15:09:51] [ $CD ] macros:
[15:09:51] [ $CD ] startup_line0:
[15:09:51] [ $CD ] startup_line1:
[15:09:51] [ $CD ] Macro0:
[15:09:51] [ $CD ] Macro1:
[15:09:51] [ $CD ] Macro2:
[15:09:51] [ $CD ] Macro3:
[15:09:51] [ $CD ] after_homing:
[15:09:51] [ $CD ] after_reset:
[15:09:51] [ $CD ] after_unlock:
[15:09:51] [ $CD ] start:
[15:09:51] [ $CD ] must_home: false
[15:09:51] [ $CD ] deactivate_parking: false
[15:09:51] [ $CD ] check_limits: true
[15:09:51] [ $CD ] parking:
[15:09:51] [ $CD ] enable: false
[15:09:51] [ $CD ] axis: Z
[15:09:51] [ $CD ] targetmposmm: -5.000000
[15:09:51] [ $CD ] ratemmper_min: 800.000000
[15:09:51] [ $CD ] pulloutdistancemm: 5.000000
[15:09:51] [ $CD ] pulloutratemmpermin: 250.000000
[15:09:51] [ $CD ] user_outputs:
[15:09:51] [ $CD ] analog0pin: NOPIN
[15:09:51] [ $CD ] analog1pin: NOPIN
[15:09:51] [ $CD ] analog2pin: NOPIN
[15:09:51] [ $CD ] analog3pin: NOPIN
[15:09:51] [ $CD ] analog0_hz: 5000
[15:09:51] [ $CD ] analog1_hz: 5000
[15:09:51] [ $CD ] analog2_hz: 5000
[15:09:51] [ $CD ] analog3_hz: 5000
[15:09:51] [ $CD ] digital0pin: NOPIN
[15:09:51] [ $CD ] digital1pin: NOPIN
[15:09:51] [ $CD ] digital2pin: NOPIN
[15:09:51] [ $CD ] digital3pin: NOPIN
[15:09:51] [ $CD ] digital4pin: NOPIN
[15:09:51] [ $CD ] digital5pin: NOPIN
[15:09:51] [ $CD ] digital6pin: NOPIN
[15:09:51] [ $CD ] digital7pin: NOPIN
[15:09:51] [ $CD ] user_inputs:
[15:09:51] [ $CD ] analog0pin: NOPIN
[15:09:51] [ $CD ] analog1pin: NOPIN
[15:09:51] [ $CD ] analog2pin: NOPIN
[15:09:51] [ $CD ] analog3pin: NOPIN
[15:09:51] [ $CD ] digital0pin: NOPIN
[15:09:51] [ $CD ] digital1pin: NOPIN
[15:09:51] [ $CD ] digital2pin: NOPIN
[15:09:51] [ $CD ] digital3pin: NOPIN
[15:09:51] [ $CD ] digital4pin: NOPIN
[15:09:51] [ $CD ] digital5pin: NOPIN
[15:09:51] [ $CD ] digital6pin: NOPIN
[15:09:51] [ $CD ] digital7pin: NOPIN
[15:09:51] [ $CD ] arctolerancemm: 0.002000
[15:09:51] [ $CD ] junctiondeviationmm: 0.010000
[15:09:51] [ $CD ] verbose_errors: true
[15:09:51] [ $CD ] report_inches: false
[15:09:51] [ $CD ] enableparkingoverride_control: false
[15:09:51] [ $CD ] uselinenumbers: false
[15:09:51] [ $CD ] planner_blocks: 16
[15:09:51] [ $CD ] ok
[15:09:51] [ $I ] [VER:3.9 FluidNC v3.9.8:]
[15:09:51] [ $I ] [OPT:PHS]
[15:09:51] [ $I ] [MSG:Machine: Default (Test Drive no I/O)]
[15:09:51] [ $I ] [MSG:Mode=AP:SSID=FluidNC:IP=192.168.0.1:MAC=E8-6B-EA-D8-F2-D9]
[15:09:51] [ $I ] ok
[15:09:51] [ $G ] [GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0 S0]
[15:09:51] [ $G ] ok
[15:13:45] [ $hostname=fluidnc3 ] ok
[15:14:14] [ $STA/SSID=NearFieldScanner ] ok
[15:14:42] [ $AP/SSID=FluidNC3 ] ok
[15:14:57] [ $hostname ] $Hostname=fluidnc3 ;unknown
[15:14:57] [ $hostname ] ok
[15:15:12] [ $STA/SSID ] $Sta/SSID=fluidnc3NearFieldScanner ;unknown
[15:15:12] [ $STA/SSID ] ok
[15:15:27] [ $AP/SSID ] $AP/SSID=fluidnc3NearFieldScannerFluidNC3 ;unknown
[15:15:27] [ $AP/SSID ] ok

Here is what I did:

[15:13:45] [ $hostname=fluidnc3 ] ok
[15:14:14] [ $STA/SSID=NearFieldScanner ] ok
[15:14:42] [ $AP/SSID=FluidNC3 ] ok
[15:14:57] [ $hostname ] $Hostname=fluidnc3 ;unknown
[15:14:57] [ $hostname ] ok
[15:15:12] [ $STA/SSID ] $Sta/SSID=fluidnc3NearFieldScanner ;unknown
[15:15:12] [ $STA/SSID ] ok
[15:15:27] [ $AP/SSID ] $AP/SSID=fluidnc3NearFieldScannerFluidNC3 ;unknown
[15:15:27] [ $AP/SSID ] ok

Same as with the web interface.

#3 – TomKamphuys 于 2025-08-10

3.9.7 does NOT have the problem:

[15:40:48] [ $I ] [VER:3.9 FluidNC v3.9.7:]
[15:40:48] [ $I ] [OPT:PHS]
[15:40:48] [ $I ] [MSG:Machine: Default (Test Drive no I/O)]
[15:40:48] [ $I ] [MSG:Mode=AP:SSID=FluidNC:IP=192.168.0.1:MAC=E8-6B-EA-D8-F2-D9]
[15:40:48] [ $I ] ok
[15:40:48] [ $G ] [GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0 S0]
[15:40:48] [ $G ] ok
[15:40:56] [ $hostname=fluidnc3 ] ok
[15:41:01] [ $STA/SSID=NearFieldScanner ] ok
[15:41:04] [ $AP/SSID=FluidNC3 ] ok
[15:41:08] [ $hostname ] $Hostname=fluidnc3 ;unknown
[15:41:08] [ $hostname ] ok
[15:41:11] [ $STA/SSID ] $Sta/SSID=NearFieldScanner ;unknown
[15:41:11] [ $STA/SSID ] ok
[15:41:26] [ $AP/SSID ] $AP/SSID=FluidNC3 ;unknown
[15:41:26] [ $AP/SSID ] ok

#4 – bdring 于 2025-08-10

We will look into that.

#5 – bdring 于 2025-08-10

Try this PR

https://github.com/bdring/FluidNC/pull/1543

原始Issue: https://github.com/bdring/FluidNC/issues/1542

喜欢 (0)