> 未分类 > [FluidNC Issue#1538] Problem: CLEAR ALARM button unresponsive on Chrome on Android

[FluidNC Issue#1538] Problem: CLEAR ALARM button unresponsive on Chrome on Android

未分类 bolang 4个月前 (10-14) 49次浏览

Issue #1538 | 状态: 进行中 | 作者: unklegwar | 创建时间: 2025-08-06

Wiki Search Terms

Pressing CLEAR ALARM in Chrome on Android (Galaxy S20 FE 5G, Android 13, Chrome 138.0.7204.168) only displays the Alt Text/Tool Tip most of the time.
Playing with “REQUEST DESKTOP VERSION” and rotating/unrotating screen managed to get it to work once or twice.
Most of the time, the tooltip shows, but nothing else happens.
The result is having to reset/restart and start the gcode over again.

UI note. When the gcode gets paused due to alarm, the message says to RESET to continue. But the only reset shown is reset firmware. It would be much clearer to refer to “CLEAR ALARM”.

Controller Board

Jackpot CNC from V1 Engineering

Machine Description

Lowrider v4 (V1 Engineering)

Input Circuits

Configuration file

board: Jackpot TMC2209
name: LowRider
meta: 10-31-2024 RyanZ
stepping: 
  engine: I2S_STATIC
  idle_ms: 255
  pulse_us: 2
  dirdelayus: 1
  disabledelayus: 0
  segments: 12
uart1: 
  txd_pin: gpio.0
  rxd_pin: gpio.4
  rtspin: NOPIN
  ctspin: NOPIN
  baud: 115200
  mode: 8N1
  passthrough_baud: 0
  passthrough_mode: 8E1
i2so: 
  bck_pin: gpio.22
  data_pin: gpio.21
  ws_pin: gpio.17
  minpulseus: 2
spi: 
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18
sdcard: 
  cs_pin: gpio.5
  carddetectpin: NO_PIN
  frequency_hz: 20000000
kinematics: 
  Cartesian: 
axes: 
  sharedstepperdisablepin: NOPIN
  sharedstepperresetpin: NOPIN
  homing_runs: 2
  x: 
    stepspermm: 50.000000
    maxratemmpermin: 9000.000000
    accelerationmmper_sec2: 200.000000
    maxtravelmm: 1525.000000
    soft_limits: true
    homing: 
      cycle: 2
      allowsingleaxis: true
      positive_direction: false
      mpos_mm: 3.000000
      feedmmper_min: 300.000000
      seekmmper_min: 1500.000000
      settle_ms: 500
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: gpio.25
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 2.000000
      tmc_2209: 
        addr: 0
        cspin: NOPIN
        uart_num: 1
        step_pin: I2SO.2
        direction_pin: I2SO.1
        disable_pin: I2SO.0
        rsenseohms: 0.110000
        run_amps: 0.800000
        hold_amps: 0.700000
        microsteps: 8
        toff_disable: 0
        toff_stealthchop: 5
        use_enable: false
        run_mode: StealthChop
        homing_mode: StealthChop
        homing_amps: 0.800000
        stallguard: 0
        stallguard_debug: false
        toff_coolstep: 3
  y: 
    stepspermm: 50.000000
    maxratemmpermin: 9000.000000
    accelerationmmper_sec2: 200.000000
    maxtravelmm: 1525.000000
    soft_limits: true
    homing: 
      cycle: 2
      allowsingleaxis: true
      positive_direction: false
      mpos_mm: 3.000000
      feedmmper_min: 300.000000
      seekmmper_min: 1500.000000
      settle_ms: 500
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: gpio.33
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 4.000000
      tmc_2209: 
        addr: 1
        cspin: NOPIN
        uart_num: 1
        step_pin: I2SO.5
        direction_pin: I2SO.4
        disable_pin: I2SO.7
        rsenseohms: 0.110000
        run_amps: 0.800000
        hold_amps: 0.700000
        microsteps: 8
        toff_disable: 0
        toff_stealthchop: 5
        use_enable: false
        run_mode: StealthChop
        homing_mode: StealthChop
        homing_amps: 0.800000
        stallguard: 0
        stallguard_debug: false
        toff_coolstep: 3
    motor1: 
      limitnegpin: gpio.35
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 8.500000
      tmc_2209: 
        addr: 3
        cs_pin: I2SO.14
        uart_num: 1
        step_pin: I2SO.13
        direction_pin: I2SO.12
        disable_pin: I2SO.15
        rsenseohms: 0.110000
        run_amps: 0.800000
        hold_amps: 0.700000
        microsteps: 8
        toff_disable: 0
        toff_stealthchop: 5
        use_enable: false
        run_mode: StealthChop
        homing_mode: StealthChop
        homing_amps: 0.800000
        stallguard: 0
        stallguard_debug: false
        toff_coolstep: 3
  z: 
    stepspermm: 200.000000
    maxratemmpermin: 1800.000000
    accelerationmmper_sec2: 80.000000
    maxtravelmm: 90.000000
    soft_limits: false
    homing: 
      cycle: 1
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 3.000000
      feedmmper_min: 200.000000
      seekmmper_min: 800.000000
      settle_ms: 500
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: gpio.32
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 4.000000
      tmc_2209: 
        addr: 2
        cspin: NOPIN
        uart_num: 1
        step_pin: I2SO.10
        direction_pin: I2SO.9
        disable_pin: I2SO.8
        rsenseohms: 0.110000
        run_amps: 0.800000
        hold_amps: 0.700000
        microsteps: 8
        toff_disable: 0
        toff_stealthchop: 5
        use_enable: false
        run_mode: StealthChop
        homing_mode: StealthChop
        homing_amps: 0.800000
        stallguard: 0
        stallguard_debug: false
        toff_coolstep: 3
    motor1: 
      limitnegpin: NO_PIN
      limitpospin: gpio.34
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 3.685000
      tmc_2209: 
        addr: 3
        cs_pin: I2SO.19
        uart_num: 1
        step_pin: I2SO.18
        direction_pin: I2SO.17
        disable_pin: I2SO.16
        rsenseohms: 0.110000
        run_amps: 0.800000
        hold_amps: 0.700000
        microsteps: 8
        toff_disable: 0
        toff_stealthchop: 5
        use_enable: false
        run_mode: StealthChop
        homing_mode: StealthChop
        homing_amps: 0.800000
        stallguard: 0
        stallguard_debug: false
        toff_coolstep: 3
control: 
  safetydoorpin: NO_PIN
  resetpin: NOPIN
  feedholdpin: NO_PIN
  cyclestartpin: NO_PIN
  macro0pin: NOPIN
  macro1pin: NOPIN
  macro2pin: NOPIN
  macro3pin: NOPIN
  faultpin: NOPIN
  estoppin: NOPIN
  homingbuttonpin: NO_PIN
coolant: 
  flood_pin: gpio.2
  mist_pin: gpio.16
  delay_ms: 0
probe: 
  pin: 'gpio.36:low'
  toolsetterpin: NOPIN
  checkmodestart: true
  hard_stop: false
macros: 
  startup_line0: 
  startup_line1: 
  Macro0: 
  Macro1: 
  Macro2: 
  Macro3: 
  after_homing: 
  after_reset: 
  after_unlock: 
start: 
  must_home: false
  deactivate_parking: false
  check_limits: true
parking: 
  enable: false
  axis: Z
  targetmposmm: -5.000000
  ratemmper_min: 800.000000
  pulloutdistancemm: 5.000000
  pulloutratemmpermin: 250.000000
user_outputs: 
  analog0pin: NOPIN
  analog1pin: NOPIN
  analog2pin: NOPIN
  analog3pin: NOPIN
  analog0_hz: 5000
  analog1_hz: 5000
  analog2_hz: 5000
  analog3_hz: 5000
  digital0_pin: gpio.26
  digital1_pin: gpio.27
  digital2pin: NOPIN
  digital3pin: NOPIN
  digital4pin: NOPIN
  digital5pin: NOPIN
  digital6pin: NOPIN
  digital7pin: NOPIN
user_inputs: 
  analog0pin: NOPIN
  analog1pin: NOPIN
  analog2pin: NOPIN
  analog3pin: NOPIN
  digital0pin: NOPIN
  digital1pin: NOPIN
  digital2pin: NOPIN
  digital3pin: NOPIN
  digital4pin: NOPIN
  digital5pin: NOPIN
  digital6pin: NOPIN
  digital7pin: NOPIN
arctolerancemm: 0.002000
junctiondeviationmm: 0.010000
verbose_errors: true
report_inches: false
enableparkingoverride_control: false
uselinenumbers: false
planner_blocks: 32

Startup Messages

$SS
[MSG:INFO: FluidNC v3.9.8 https://github.com/bdring/FluidNC]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]
[MSG:INFO: Local filesystem type is littlefs]
[MSG:INFO: Configuration file:config.yaml]
[MSG:INFO: Machine LowRider]
[MSG:INFO: Board Jackpot TMC2209]
[MSG:INFO: UART1 Tx:gpio.0 Rx:gpio.4 RTS:NO_PIN Baud:115200]
[MSG:INFO: I2SO BCK:gpio.22 WS:gpio.17 DATA:gpio.21Min Pulse:2us]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cspin:gpio.5 detect:NOPIN freq:20000000]
[MSG:INFO: Stepping:I2S_STATIC Pulse:2us Dsbl Delay:0us Dir Delay:1us Idle Delay:255ms]
[MSG:INFO: User Digital Output: 0 on Pin:gpio.26]
[MSG:INFO: User Digital Output: 1 on Pin:gpio.27]
[MSG:INFO: Axis count 3]
[MSG:INFO: Axis X (3.000,1528.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     tmc2209 UART1 Addr:0 CS:NOPIN Step:I2SO.2 Dir:I2SO.1 Disable:I2SO.0 R:0.110]
[MSG:INFO:  Neg Limit gpio.25]
[MSG:INFO: Axis Y (3.000,1528.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     tmc2209 UART1 Addr:1 CS:NOPIN Step:I2SO.5 Dir:I2SO.4 Disable:I2SO.7 R:0.110]
[MSG:INFO:  Neg Limit gpio.33]
[MSG:INFO:   Motor1]
[MSG:INFO:     tmc_2209 UART1 Addr:3 CS:I2SO.14 Step:I2SO.13 Dir:I2SO.12 Disable:I2SO.15 R:0.110]
[MSG:INFO:  Neg Limit gpio.35]
[MSG:INFO: Axis Z (-87.000,3.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     tmc2209 UART1 Addr:2 CS:NOPIN Step:I2SO.10 Dir:I2SO.9 Disable:I2SO.8 R:0.110]
[MSG:INFO:  Pos Limit gpio.32]
[MSG:INFO:   Motor1]
[MSG:INFO:     tmc_2209 UART1 Addr:3 CS:I2SO.19 Step:I2SO.18 Dir:I2SO.17 Disable:I2SO.16 R:0.110]
[MSG:INFO:  Pos Limit gpio.34]
[MSG:INFO: X Axis driver test passed]
[MSG:INFO: Y Axis driver test passed]
[MSG:INFO: Y2 Axis driver test passed]
[MSG:INFO: Z Axis driver test passed]
[MSG:INFO: Z2 Axis driver test passed]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: Connecting to STA SSID:REDACTED]
[MSG:INFO: Connecting.]
[MSG:INFO: Connecting..]
[MSG:INFO: Connected - IP is 10.0.0.28]
[MSG:INFO: WiFi on]
[MSG:INFO: Start mDNS with hostname:http://Lowrider.local/]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]
[MSG:INFO: Flood coolant gpio.2]
[MSG:INFO: Mist coolant gpio.16]
[MSG:INFO: Probe gpio.36:low]
ok

User Interface Software

ESP3D

What happened?

Got an alarm because of exceeding Max X travel. gcode paused. Prompted me to reset. Just says “reset”, but the only thing labeled RESET it the reset firmware button. This did not clear the alarm and allow me to continue.

I figured out it meant the Clear Alarm, but that worked once, maybe twice in dozens of reboots and restarts. Rest of the time, it just displays the tooltip and nothing gets cleared.

GCode File

No response

Other Information

No response

原始Issue: https://github.com/bdring/FluidNC/issues/1538

喜欢 (0)