> 未分类 > [FluidNC Issue#1486] Problem: No SD card

[FluidNC Issue#1486] Problem: No SD card

未分类 bolang 4个月前 (10-14) 35次浏览

Issue #1486 | 状态: 已关闭 | 作者: ZASto | 创建时间: 2025-04-29

Wiki Search Terms

SD card not visible by the controller.
Tried with different frequencies but no luck.
Card is 16Gbytes formatted as FAT 32 bit version.

Controller Board

6x CNC Controller

Machine Description

Homemade router

Input Circuits

Configuration file

board: 6x CNC Controller
name: 6x Default
stepping:
  engine: I2S_STREAM
  idle_ms: 255
  pulse_us: 4
  dirdelayus: 1
  disabledelayus: 0
axes:
  sharedstepperdisablepin: NOPIN
  x:
    stepspermm: 40.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 600.000
    soft_limits: false
    homing:
      cycle: 2
      positive_direction: false
      mpos_mm: 0.000
      feedmmper_min: 100.000
      seekmmper_min: 200.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.2:low:pu
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: false
      pulloff_mm: 1.000
      standard_stepper:
        step_pin: I2SO.2
        direction_pin: I2SO.1
        disable_pin: I2SO.0
  y:
    stepspermm: 40.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 900.000
    soft_limits: false
    homing:
      cycle: 2
      positive_direction: true
      mpos_mm: 0.000
      feedmmper_min: 100.000
      seekmmper_min: 200.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.26:low:pu
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: false
      pulloff_mm: 1.000
      standard_stepper:
        step_pin: I2SO.5
        direction_pin: I2SO.4
        disable_pin: I2SO.7
  z:
    stepspermm: 40.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 100.000
    soft_limits: false
    homing:
      cycle: 1
      positive_direction: true
      mpos_mm: 0.000
      feedmmper_min: 100.000
      seekmmper_min: 800.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.33:low    
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: false
      pulloff_mm: 1.000
      standard_stepper:
        step_pin: I2SO.10
        direction_pin: I2SO.9
        disable_pin: I2SO.8
        
i2so:
  bck_pin: gpio.22
  data_pin: gpio.21
  ws_pin: gpio.17
spi:
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18
sdcard:
  carddetectpin: NO_PIN
  cs_pin: gpio.5
  frequency_hz: 8000000
  
probe:
  pin: gpio.39:low
  toolsetter_pin: gpio.36:low
  

Using MOSFETs (Check Spindle Pin Usage

coolant:
  flood_pin: gpio.12
  mist_pin: gpio.4
  delay_ms: 0
start:
  must_home: false
  

#begin PWM

pwm:
  pwm_hz: 5000
  direction_pin: gpio.15
  output_pin: gpio.13
  enable_pin: gpio.14
  disablewiths0: false
  s0withdisable: true
  spinup_ms: 0
  spindown_ms: 0
  tool_num: 0
  speed_map: 0=0.000% 10000=100.000%
  offonalarm: false

Startup Messages

[MSG:INFO: FluidNC v3.9.6 https://github.com/bdring/FluidNC]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]
[MSG:INFO: Local filesystem type is littlefs]
[MSG:INFO: Configuration file:config.yaml]
[MSG:INFO: Machine 6x Default]
[MSG:INFO: Board 6x CNC Controller]
[MSG:INFO: I2SO BCK:gpio.22 WS:gpio.17 DATA:gpio.21Min Pulse:2us]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cspin:gpio.5 detect:NOPIN freq:8000000]
[MSG:INFO: Stepping:I2S_STREAM Pulse:4us Dsbl Delay:0us Dir Delay:1us Idle Delay:255ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: Axis X (0.000,600.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standard_stepper Step:I2SO.2 Dir:I2SO.1 Disable:I2SO.0]
[MSG:INFO:  Neg Limit gpio.2:low:pu]
[MSG:INFO: Axis Y (-900.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standard_stepper Step:I2SO.5 Dir:I2SO.4 Disable:I2SO.7]
[MSG:INFO:  Neg Limit gpio.26:low:pu]
[MSG:INFO: Axis Z (-100.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standard_stepper Step:I2SO.10 Dir:I2SO.9 Disable:I2SO.8]
[MSG:INFO:  Neg Limit gpio.33:low]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: STA SSID is not set]
[MSG:INFO: AP SSID FluidNC IP 192.168.0.1 mask 255.255.255.0 channel 1]
[MSG:INFO: AP started]
[MSG:INFO: WiFi on]
[MSG:INFO: Captive Portal Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]
[MSG:INFO: PWM Spindle Ena:gpio.14 Out:gpio.13 Dir:gpio.15 Freq:5000Hz Period:8191]
[MSG:INFO: Flood coolant gpio.12]
[MSG:INFO: Mist coolant gpio.4]
[MSG:INFO: Probe gpio.39:low]
[MSG:INFO: Toolsetter gpio.36:low]

User Interface Software

WebUI

What happened?

Refreshing SD card gives error 0x106

GCode File

No response

Other Information

No response

评论 (5)

#1 – bdring 于 2025-04-29

We use the standard SD code from the Espressif libraries. The 6x has been extensively tested with SD cards.

The problem is typically with the SD card.
– What brand is the SD card?
– Can you try some other cards?
– Have you tried everything mentioned on the SD card wiki page?

#2 – ramack 于 2025-05-02

SDCard works fine for me on the 6x CNC Controller.

I read that using the STA mode for Wifi could cause trouble in some places, did you try to connect to an AP? Did you inspect the board optically? Is all soldering looking fine – sure all should be good with a new board out of production, but it could be worth a look.

#3 – mkl974 于 2025-06-23

idem..no sd card

#4 – spanzetta 于 2025-08-06

same here.. using ESP32-CAM with latest v3.9.8

#5 – MitchBradley 于 2025-08-06

> same here.. using ESP32-CAM with latest v3.9.8

FluidNC does not support ESP32-CAM because it uses WROVER instead of WROOM modules. http://wiki.fluidnc.com/en/hardware/esp32pinreference#esp32-pin-reference

原始Issue: https://github.com/bdring/FluidNC/issues/1486

喜欢 (0)