> 未分类 > [FluidNC Issue#1480] Problem: SD card is inaccessible: ESP_ERR_INVALID_CRC sdmmc_io_reset: unexpected return: 0x109

[FluidNC Issue#1480] Problem: SD card is inaccessible: ESP_ERR_INVALID_CRC sdmmc_io_reset: unexpected return: 0x109

未分类 bolang 4个月前 (10-14) 51次浏览

Issue #1480 | 状态: 已关闭 | 作者: Qniansi | 创建时间: 2025-04-16

Wiki Search Terms

sd

Controller Board

6-pack

Machine Description

none

Input Circuits

Configuration file

board: 6 Pack
name: New configuration
meta: 
stepping: 
  engine: RMT
  idle_ms: 250
  pulse_us: 4
  dirdelayus: 0
  disabledelayus: 0
  segments: 12
spi: 
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18
sdcard: 
  cs_pin: gpio.17
  carddetectpin: NO_PIN
  frequency_hz: 400000
kinematics: 
  CartesianRTCP: 
axes: 
  sharedstepperdisablepin: NOPIN
  sharedstepperresetpin: NOPIN
  homing_runs: 2
  x: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 2
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.33:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.5
        direction_pin: gpio.4
        disablepin: NOPIN
  y: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 3
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.34:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.13
        direction_pin: gpio.12
        disablepin: NOPIN
  z: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 1
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.35:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.15
        direction_pin: gpio.14
        disablepin: NOPIN
  a: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 4
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.36:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.22
        direction_pin: gpio.21
        disablepin: NOPIN
  b: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 5
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.39:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.26
        direction_pin: gpio.25
        disablepin: NOPIN
  c: 
    stepspermm: 80.000000
    maxratemmpermin: 1000.000000
    accelerationmmper_sec2: 25.000000
    maxtravelmm: 1000.000000
    soft_limits: false
    homing: 
      cycle: 6
      allowsingleaxis: true
      positive_direction: true
      mpos_mm: 0.000000
      feedmmper_min: 50.000000
      seekmmper_min: 200.000000
      settle_ms: 250
      seek_scaler: 1.100000
      feed_scaler: 1.100000
    motor0: 
      limitnegpin: NO_PIN
      limitpospin: NO_PIN
      limitallpin: gpio.16:low
      hard_limits: false
      pulloff_mm: 1.000000
      standard_stepper: 
        step_pin: gpio.32
        direction_pin: gpio.27
        disablepin: NOPIN
control: 
  safetydoorpin: NO_PIN
  resetpin: NOPIN
  feedholdpin: NO_PIN
  cyclestartpin: NO_PIN
  macro0pin: NOPIN
  macro1pin: NOPIN
  macro2pin: NOPIN
  macro3pin: NOPIN
  faultpin: NOPIN
  estoppin: NOPIN
coolant: 
  floodpin: NOPIN
  mistpin: NOPIN
  delay_ms: 0
probe: 
  pin: gpio.37
  toolsetterpin: NOPIN
  checkmodestart: false
  hard_stop: false
macros: 
  startup_line0: 
  startup_line1: 
  Macro0: 
  Macro1: 
  Macro2: 
  Macro3: 
  after_homing: 
  after_reset: 
  after_unlock: 
start: 
  must_home: true
  deactivate_parking: false
  check_limits: true
parking: 
  enable: false
  axis: Z
  targetmposmm: -5.000000
  ratemmper_min: 800.000000
  pulloutdistancemm: 5.000000
  pulloutratemmpermin: 250.000000
user_outputs: 
  analog0pin: NOPIN
  analog1pin: NOPIN
  analog2pin: NOPIN
  analog3pin: NOPIN
  analog0_hz: 5000
  analog1_hz: 5000
  analog2_hz: 5000
  analog3_hz: 5000
  digital0pin: NOPIN
  digital1pin: NOPIN
  digital2pin: NOPIN
  digital3pin: NOPIN
  digital4pin: NOPIN
  digital5pin: NOPIN
  digital6pin: NOPIN
  digital7pin: NOPIN
user_inputs: 
  analog0pin: NOPIN
  analog1pin: NOPIN
  analog2pin: NOPIN
  analog3pin: NOPIN
  digital0pin: NOPIN
  digital1pin: NOPIN
  digital2pin: NOPIN
  digital3pin: NOPIN
  digital4pin: NOPIN
  digital5pin: NOPIN
  digital6pin: NOPIN
  digital7pin: NOPIN
10V: 
  forwardpin: NOPIN
  reversepin: NOPIN
  pwm_hz: 5000
  directionpin: NOPIN
  output_pin: gpio.2
  enablepin: NOPIN
  disablewiths0: false
  s0withdisable: true
  spinup_ms: 0
  spindown_ms: 0
  tool_num: 100
  speed_map: 0=0.00% 0=30.00% 6000=30.00% 20000=100.00%
  offonalarm: false
  atc: 
  m6_macro: 
arctolerancemm: 0.002000
junctiondeviationmm: 0.010000
verbose_errors: true
report_inches: false
enableparkingoverride_control: false
uselinenumbers: false
planner_blocks: 16

Startup Messages

[MSG:INFO: FluidNC v3.9.5 (minz-f9f2a46c-dirty) https://github.com/bdring/FluidNC.git]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]
[MSG:INFO: Local filesystem type is littlefs]
[MSG:INFO: Configuration file:config.yaml]
[MSG:INFO: Machine New configuration]
[MSG:INFO: Board 6 Pack]
[MSG:INFO: SPI SCK:gpio.18 MOSI:gpio.23 MISO:gpio.19]
[MSG:INFO: SD Card cspin:gpio.17 detect:NOPIN freq:8000000]
[MSG:INFO: Stepping:RMT Pulse:4us Dsbl Delay:0us Dir Delay:0us Idle Delay:250ms]
[MSG:INFO: Axis count 6]
[MSG:INFO: Axis X (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.5 Dir:gpio.4 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.33:low]
[MSG:INFO: Axis Y (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.13 Dir:gpio.12 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.34:low]
[MSG:INFO: Axis Z (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.15 Dir:gpio.14 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.35:low]
[MSG:INFO: Axis A (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.22 Dir:gpio.21 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.36:low]
[MSG:INFO: Axis B (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.26 Dir:gpio.25 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.39:low]
[MSG:INFO: Axis C (-1000.000,0.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     standardstepper Step:gpio.32 Dir:gpio.27 Disable:NOPIN]
[MSG:INFO:  All Limit gpio.16:low]
[MSG:INFO: Kinematic system: CartesianRTCP]
[MSG:INFO: STA SSID is not set]
[MSG:INFO: AP SSID FluidNC IP 192.168.0.1 mask 255.255.255.0 channel 1]
[MSG:INFO: AP started]
[MSG:INFO: WiFi on]
[MSG:INFO: Captive Portal Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: 10V Spindle Ena:NOPIN Out:gpio.2 Dir:NOPIN Fwd:NOPIN Rev:NOPIN Freq:5000Hz Period:8191]
[MSG:INFO: Probe gpio.37]
ok
ok

User Interface Software

No response

What happened?

Unable to read SD card, pin is using gpio.17, and changing the frequency to 400000, 1000000, 10000000 is not available. What is the reason for this

!Image

!Image

!Image

!Image

GCode File

No response

Other Information

No response

原始Issue: https://github.com/bdring/FluidNC/issues/1480

喜欢 (0)