> 未分类 > [FluidNC Issue#1439] Problem: MKT TS35 R V-2.0 display stays black on power

[FluidNC Issue#1439] Problem: MKT TS35 R V-2.0 display stays black on power

未分类 bolang 4个月前 (10-14) 40次浏览

Issue #1439 | 状态: 已关闭 | 作者: xmarduel | 创建时间: 2025-01-26

Wiki Search Terms

MKT TS35 -R V2.0

Controller Board

MKS DLC32 V2.1

Machine Description

CNC 1419 Router

Input Circuits

Configuration file

board: MKS-DLC32 V2.1
name: CNC 1419
meta: (01.01.2025) by XAM
kinematics:
  Cartesian:
stepping:
  engine: I2S_STATIC
  idle_ms: 0
  pulse_us: 4
  dirdelayus: 1
  disabledelayus: 0
axes:
  sharedstepperdisable_pin: I2SO.0
  x:
    stepspermm: 800.0
    maxratemmpermin: 1000.000
    accelerationmmper_sec2: 50.000
    maxtravelmm: 150.000
    soft_limits: false
    homing:
      cycle: 1
      positive_direction: false
      mpos_mm: 0.000
      feedmmper_min: 300.000
      seekmmper_min: 5000.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.36
      hard_limits: false
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.1
        direction_pin: I2SO.2
  y:
    stepspermm: 800.0
    maxratemmpermin: 1000.000
    accelerationmmper_sec2: 50.000
    maxtravelmm: 200.000
    soft_limits: false
    homing:
      cycle: 1
      positive_direction: false
      mpos_mm: 0.000
      feedmmper_min: 300.000
      seekmmper_min: 5000.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.35
      hard_limits: false
      pulloff_mm: 2.000
      stepstick:
        step_pin: I2SO.5
        direction_pin: I2SO.6:low
  z:
    stepspermm: 800.0
    maxratemmpermin: 500.000
    accelerationmmper_sec2: 50.000
    maxtravelmm: 80.000
    soft_limits: false
    homing:
      cycle: 0
      positive_direction: false
      mpos_mm: 0.000
      feedmmper_min: 300.000
      seekmmper_min: 1000.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100
    motor0:
      limitnegpin: gpio.34
      hard_limits: false
      pulloff_mm: 1.000
      stepstick:
        step_pin: I2SO.3
        direction_pin: I2SO.4
i2so:
  bck_pin: gpio.16
  data_pin: gpio.21
  ws_pin: gpio.17
spi:
  miso_pin: gpio.12
  mosi_pin: gpio.13
  sck_pin: gpio.14
sdcard:
  cs_pin: gpio.15
  carddetectpin: NO_PIN
control:
  safetydoorpin: NO_PIN
  resetpin: NOPIN
  feedholdpin: NO_PIN
  cyclestartpin: NO_PIN
  macro0_pin: gpio.33:low:pu
  macro1pin: NOPIN
  macro2pin: NOPIN
  macro3pin: NOPIN
macros:
  startup_line0:
  startup_line1:
  macro0: $SD/Run=lasertest.gcode
  macro1: $SD/Run=home.gcode
  macro2:
  macro3:
coolant:
  floodpin: NOPIN
  mistpin: NOPIN
  delay_ms: 0
probe:
  pin: gpio.22
  checkmodestart: true
Laser:
  pwm_hz: 5000
  #L on Beeper / IN on TTL
  output_pin: gpio.32
  enable_pin: I2SO.7
  disablewiths0: false
  s0withdisable: false
  tool_num: 0
  speed_map: 0=0.000% 0=12.500% 1700=100.000%

135=0mA 270=5mA 400=10mA 700=16mA

user_outputs:
  analog0pin: NOPIN
  analog1pin: NOPIN
  analog2pin: NOPIN
  analog3pin: NOPIN
  analog0_hz: 5000
  analog1_hz: 5000
  analog2_hz: 5000
  analog3_hz: 5000
  digital0pin: NOPIN
  digital1pin: NOPIN
  digital2pin: NOPIN
  digital3pin: NOPIN
start:
  must_home: false
5,18,19,22,23,25,26,27,32,33,39,I2SO.7


SDA 0 / SCL 4

Startup Messages

$G
$SS
[MSG:INFO: FluidNC v3.9.1 https://github.com/bdring/FluidNC]
[MSG:INFO: Compiled with ESP32 SDK:v4.4.7-dirty]
[MSG:INFO: Local filesystem type is spiffs]
[MSG:INFO: Configuration file:config.yaml]
[MSG:INFO: Machine CNC 1419]
[MSG:INFO: Board MKS-DLC32 V2.1]
[MSG:INFO: I2SO BCK:gpio.16 WS:gpio.17 DATA:gpio.21]
[MSG:INFO: SPI SCK:gpio.14 MOSI:gpio.13 MISO:gpio.12]
[MSG:INFO: SD Card cspin:gpio.15 detect:NOPIN freq:8000000]
[MSG:INFO: Stepping:I2S_STATIC Pulse:4us Dsbl Delay:0us Dir Delay:1us Idle Delay:0ms]
[MSG:INFO: Axis count 3]
[MSG:INFO: Shared stepper disable I2SO.0]
[MSG:INFO: Axis X (0.000,150.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     stepstick Step:I2SO.1 Dir:I2SO.2 Disable:NO_PIN]
[MSG:INFO:  X Neg Limit gpio.36]
[MSG:INFO: Axis Y (0.000,200.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     stepstick Step:I2SO.5 Dir:I2SO.6:low Disable:NO_PIN]
[MSG:INFO:  Y Neg Limit gpio.35]
[MSG:INFO: Axis Z (0.000,80.000)]
[MSG:INFO:   Motor0]
[MSG:INFO:     stepstick Step:I2SO.3 Dir:I2SO.4 Disable:NO_PIN]
[MSG:INFO:  Z Neg Limit gpio.34]
[MSG:INFO: macro0_pin gpio.33:low:pu]
[MSG:INFO: Kinematic system: Cartesian]
[MSG:INFO: STA SSID is not set]
[MSG:INFO: AP SSID FluidNC IP 192.168.0.1 mask 255.255.255.0 channel 1]
[MSG:INFO: AP started]
[MSG:INFO: WiFi on]
[MSG:INFO: Captive Portal Started]
[MSG:INFO: HTTP started on port 80]
[MSG:INFO: Telnet started on port 23]
[MSG:INFO: Laser Ena:I2SO.7 Out:gpio.32 Freq:5000Hz Period:8191]
[MSG:INFO: Probe gpio.22]
ok

User Interface Software

No response

What happened?

When powering the MKS DLC V2.1, the MKT TS35-R V2.0 is powered (its displays becomes white for a fraction of a second) but then switches to black.

Note that it had worked initially.
Only after having erased and re-installed the firmware FluidNC-3.9.1 the problem occured.

Or did I burned the MKT TS35 by once putting the EXP-1 and EXP-2 in the wrong slots ?

GCode File

No response

Other Information

No response

评论 (5)

#1 – bdring 于 2025-01-26

We don’t support that display.

#2 – xmarduel 于 2025-01-26

What do you exactly mean by “don’t support”. This Display is sold together with the board on aliExpress. And it worked initially.
Which display would you then recommand?

Or what was the initial firmware installed on the board so that the display worked?

Thanks

#3 – bdring 于 2025-01-26

The controller and display was designed to run with their firmware. The controller can run FluidNC, be we don’t support any LCDs like that. We only support UART based smart displays and pendants.

http://wiki.fluidnc.com/en/hardware/pendants_displays

#4 – MitchBradley 于 2025-01-26

MKS took our code and modified it to use their display. That modified version is what is preinstalled on their board. Our stock version does not have their mods. Their mods are not usable with any other FluidNC boards from other vendors. They do not pay us anything, and we have no incentive to spend a lot of our time supporting their modifications. You could ask the vendor to support it, since they took your money.

#5 – xmarduel 于 2025-01-26

Thanks for your explanation. Now I understand.
Best regards
XM

原始Issue: https://github.com/bdring/FluidNC/issues/1439

喜欢 (0)