Wiki Search Terms

fluidnc installation

Controller Board

6x cnc controller v1.2

Machine Description

queenbee ultra 750 x 1000

Input Circuits

No response

Configuration file

board: 6x
name: 6x Eds xyyz 
stepping:
  engine: I2S_STREAM
  idle_ms: 255
  pulse_us: 4
  dirdelayus: 1
  disabledelayus: 0

axes:
  sharedstepperdisablepin: NOPIN
  x:
    stepspermm: 90.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 590.000
    soft_limits: false
    homing:
      cycle: 2
      positive_direction: false
      mpos_mm: 150.000
      feedmmper_min: 100.000
      seekmmper_min: 200.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limitnegpin: gpio.26:low:pu
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 5.000
      standard_stepper:
        step_pin: I2SO.5
        direction_pin: I2SO.4
        disable_pin: I2SO.7

  y:
    stepspermm: 90.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 755.000
    soft_limits: false
    homing:
      cycle: 2
      positive_direction: true
      mpos_mm: 150.000
      feedmmper_min: 100.000
      seekmmper_min: 200.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limitnegpin: gpio.33:low:pu
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 5.000
      standard_stepper:
        step_pin: I2SO.10
        direction_pin: I2SO.9
        disable_pin: I2SO.8

    motor1:
      limitnegpin: gpio.32:low:pu
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 5.000
      standard_stepper:
        step_pin: I2SO.13
        direction_pin: I2SO.12
        disable_pin: I2SO.15

  z:
    stepspermm: 90.000
    maxratemmpermin: 5000.000
    accelerationmmper_sec2: 100.000
    maxtravelmm: 140.000
    soft_limits: false
    homing:
      cycle: 1
      positive_direction: true
      mpos_mm: 150.000
      feedmmper_min: 100.000
      seekmmper_min: 800.000
      settle_ms: 500
      seek_scaler: 1.100
      feed_scaler: 1.100

    motor0:
      limitnegpin: gpio.35:low    
      limitpospin: NO_PIN
      limitallpin: NO_PIN
      hard_limits: true
      pulloff_mm: 5.000
      standard_stepper:
        step_pin: I2SO.2
        direction_pin: I2SO.1
        disable_pin: I2SO.0
       
i2so:
  bck_pin: gpio.22
  data_pin: gpio.21
  ws_pin: gpio.17

spi:
  miso_pin: gpio.19
  mosi_pin: gpio.23
  sck_pin: gpio.18

sdcard:
  carddetectpin: NO_PIN
  cs_pin: gpio.5
  
probe:
  pin: gpio.39:low
  toolsetter_pin: gpio.36:low
  
Using MOSFETs (Check Spindle Pin Usage

coolant:
  flood_pin: gpio.12
  mist_pin: gpio.4
  delay_ms: 0

start:
  must_home: false
  
Begin H100  

uart1:
  txd_pin: gpio.15
  rxd_pin: gpio.16
  rts_pin: gpio.14
  baud: 9600
  mode: 8N1

H100:
  uart_num: 1
  modbus_id: 1
  tool_num: 0
  speed_map: 0=0% 0=25% 6000=25% 24000=100%
  offonalarm: false

Startup Messages

not getting a startup message

User Interface Software

web installer, fluidterm

What happened?

6x cnc controller, says controller “does not appear to have fluid installed”, I reinstall, it says installed hit continue and it goes back to fluidnc “does not appear to be installed”. tried installing via fluidterm, loads then gives msg error reset…..If i power the unit off for 15-30min then go back into web installer it open and allows me to access the board along with config files etc. after 5min it drops out and goes back to “does not appear to have fluid installed”…machine ran yesterday
!20250102_105557
!20250102_105614

GCode File

No response

Other Information

No response